Comparative Assessments of Dental Resin Composites: A Focus on Dense Microhybrid Materials.

The performance of dental resin composites is crucially influenced by the sizes and distributions of inorganic fillers. Despite the investigation of a variety of functional particles, glass fillers and nanoscale silica are still the predominant types in dental materials. However, achieving an overall improvement in the performance of resin composites through the optimization of their formulations remains a challenge. This work introduced a "dense" microhybrid filler system with 85 wt % filler loading, leading to the preparation of self-developed resin composites (SRCs). Comparative evaluations of these five SRCs against four commercial products were performed, including mechanical property, polymerization conversion, and shrinkage, along with water sorption and solubility and wear resistance. The results showed that among all SRC groups, SRC3 demonstrated superior mechanical performance, high polymerization conversion, reduced shrinkage, low water absorption and solubility, and acceptable wear resistance. In contrast to commercial products, this optimal SRC3 material was comparable to Z350 XT in flexural and diametral tensile strength and better in flexural modulus and surface hardness. The use of a "dense" microhybrid filler system in the development of resin composites provides a balance between physicochemical property and wear resistance, which may be a promising strategy for the development of composite products.

Eliminating the Adverse Impact of Composition Modulation in Perovskite Light-Emitting Diodes toward Ultra-High Brightness and Stability.

Excess ammonium halides as composition additives are widely employed in perovskite light-emitting diodes (PeLEDs), aiming to achieve high performance by controlling crystallinity and passivating defects. However, an in-depth understanding of whether excess organoammonium components affect the film physical/electrical properties and the resultant device instability is still lacking. Here, the trade-off between the performance and stability in high-efficiency formamidinium lead iodide (FAPbI3)-based PeLEDs with excess ammonium halides is pointed, and the underlying mechanism is explored. Systematic experimental and theoretical studies reveal that excess halide salt-induced ion-doping largely alters the PeLEDs properties (e.g., carrier injection, field-dependent ion-drifting, defect physics, and phase stability). A surface clean assisted cross-linking strategy is demonstrated to eliminate the adverse impact of composition modulation and boost the operational stability without sacrificing the efficiency, achieving a high efficiency of 23.6%, a high radiance of 964 W sr-1 m-2 (The highest value for FAPbI3 based PeLEDs), and a prolong lifetime of 106.1 h at large direct current density (100 mA cm-2), concurrently. The findings uncovered an important link between excess halide salts and the device performance, providing a guideline for rational design of stable, bright, and high efficiency PeLEDs.

Efficient Electrosynthesis of Hydrogen Peroxide Using Oxygen-Doped Porous Carbon Catalysts at Industrial Current Densities.

Metal-free carbon catalysts (MFCCs) are one of the commonly used catalysts for electrocatalytic two-electron oxygen reduction (2e- ORR) synthesis of hydrogen peroxide (H2O2). Oxygen doping is an effective means to improve the performance of MFCCs, but the performance of oxygen-doped carbon catalysts is still not high enough, and the contribution of different oxygen functional groups (OFGs) to the catalytic performance is still inconclusive. In this paper, carbon-based catalysts with different oxygen contents and ratios of OFGs were prepared, and the high 2e- ORR activity of COOH + C-OH was demonstrated by combining the results of experiments and theoretical calculations. The prepared oxygen-doped carbon-based catalyst C-0.1M80 achieved an onset potential of 0.795 V (vs RHE), a selectivity of up to 98.2% (0.6 V vs RHE), and a H2O2 oxidation current of 1.33 mA cm-2 (0.5 V vs RHE) in a rotating ring-disk electrode test (0.1 M KOH solution), which was an outstanding performance in MFCCs. In a solid electrolyte flow cell, C-0.1M80 achieved a Faraday efficiency of 97.5% at 200 mA cm-2 with a corresponding H2O2 production rate of 123.7 mg cm-2 h-1. In addition, a flow cell stability test was performed at an industrial current density (100 mA cm-2) with an astounding 200 h of uninterrupted operation, also achieving an outstanding average Faradaic efficiency (95.8%).

Rolling forms the diversities of small molecular nonvolatile metabolite profile and consequently shapes the bacterial community structure for Keemun black tea.

The detailed dynamics of small molecular nonvolatile chemical and bacterial diversities, as well as their relationship are still unclear in the manufacturing process of Keemun black tea (KMBT). Herein, mass spectrometry-based untargeted metabolomics, Feature-based Molecular Networking (FBMN) and bacterial DNA amplicon sequencing were used to investigate the dense temporal samples of the manufacturing process. For the first time, we reveal that the pyrogallol-type catechins are oxidized asynchronously before catechol-type catechins during the black tea processing. Rolling is the key procedure for forming the small molecular nonvolatile metabolite profile (SMNMetProf), increasing the metabolite richness, and then shaping the bacterial community structure in the KMBT manufacturing process, which decreases both molecular weight and molecular polarity of the small molecular nonvolatile metabolites. The SMNMetProf of black tea is formed by the endogenous enzymatic oxidation of tea leaves, rather than bacterial fermentation.

Thiol-Functionalized Conjugated Metal-Organic Frameworks for Stable and Efficient Perovskite Photovoltaics.

Metal-organic frameworks (MOFs) have been investigated recently in perovskite photovoltaics owing to their potential to boost optoelectronic performance and device stability. However, the impact of variations in the MOF side chain on perovskite characteristics and the mechanism of MOF/perovskite film formation remains unclear. In this study, three nanoscale thiol-functionalized UiO-66-type Zr-based MOFs (UiO-66-(SH)2 , UiO-66-MSA, and UiO-66-DMSA) are systematically employed and examined in perovskite solar cells (PSCs). Among these MOFs, UiO-66-(SH)2 , with its rigid organic ligands, exhibited a strong interaction with perovskite materials with more efficient suppression of perovskite vacancy defects. More importantly, A detailed and in-depth discussion is provided on the formation mechanism of UiO-66-(SH)2 -assisted perovskite film upon in situ GIWAXS performed during the annealing process. The incorporation of UiO-66-(SH)2 additives substantially facilitates the conversion of PbI2 into the perovskite phase, prolongs the duration of stage I, and induces a delayed phase transformation pathway. Consequently, the UiO-66-(SH)2 -assisted device demonstrates reduced defect density and superior optoelectronic properties with optimized power conversion efficiency of 24.09% and enhanced long-term stability under ambient environment and continuous light illumination conditions. This study acts as a helpful design guide for desired MOF/perovskite structures, enabling further advancements in MOF/perovskite optoelectronic devices.

microRNA-365 attenuated intervertebral disc degeneration through modulating nucleus pulposus cell apoptosis and extracellular matrix degradation by targeting EFNA3.

This present study is aimed to investigate the role of microRNA-365 (miR-365) in the development of intervertebral disc degeneration (IDD). Nucleus pulposus (NP) cells were transfected by miR-365 mimic and miR-365 inhibitor, respectively. Concomitantly, the transfection efficiency and the expression level of miRNA were detected by quantitative reverse transcription polymerase chain reaction (qRT-PCR). Meanwhile, NP cells apoptosis was measured through propidium iodide (PI)-AnnexinV-fluorescein isothiocyanate (FITC) apoptosis detection kit. Subsequently, immunofluorescence (IF) staining was performed to assess the expression of collagen II, aggrecan and matrix metalloproteinase 13 (MMP-13). In addition, bioinformatic prediction and Luciferase reporter assay were used to reveal the target gene of miR-365. Finally, we isolated the primary NP cells from rats and injected NP-miR-365 in rat IDD models. The results showed that overexpression of miR-365 could effectively inhibit NP cells apoptosis and MMP-13 expression and upregulate the expression of collagen II and aggrecan. Conversely, suppression of miR-365 enhanced NP cell apoptosis and elevated MMP-13 expression, but decreased the expression of collagen II and aggrecan. Moreover, the further data demonstrated that miR-365 mediated NP cell degradation through targeting ephrin-A3 (EFNA3). In addition, the cells apoptosis and catabolic markers were increased in NP cells when EFNA3 upregulated. More importantly, the vivo data supported that miR-365-NP cells injection ameliorated IDD in rats models. miR-365 could alleviate the development of IDD by regulating NP cell apoptosis and ECM degradation, which is likely mediated by targeting EFNA3. Therefore, miR-365 may be a promising therapeutic avenue for treatment IDD through EFNA3.

Feasibility of Two-Screw Anterior Fixation for Odontoid Fractures in a Chinese Population: A Morphometric Study Based on Computed Tomography.

Background: To evaluate the feasibility of treating odontoid fractures in the Chinese population with two cortical screws based on computed tomography (CT) scans and describe a new measurement strategy to guide screw insertion in treating these fractures. Methods: A retrospective review of cervical computed tomographic scans of 128 patients (aged 18-76 years; men, 55 [43.0%]) was performed. The minimum external transverse diameter (METD), minimum external anteroposterior diameter (MEAD), maximum screw length (MSL), and screw projection back angle (SPBA) of the odontoid process were measured on coronal and sagittal CT images. Results: The mean values of METD and MEAD were 10.0 ± 1.1 mm and 12.0 ± 1.0 mm, respectively, in men and 9.2 ± 1.0 mm and 11.0 ± 1.0 mm, respectively, in women. Both measurements were significantly higher in men (p < 0.001). In total, 87 individuals (68%) had METD > 9.0 mm that could accommodate two 3.5-mm cortical screws. The mean MSL value and SPBA range were 34.4 ± 2.9 mm and 13.5°-24.2°, respectively, with no statistically significant difference between men and women. Conclusions: The insertion of two 3.5-mm cortical screws was possible for anterior fixation of odontoid fractures in 87 patients (68%) in our study, and there was a statistically significant difference between men and women.

Dynamic Changes in the Microbial Community and Metabolite Profile during the Pile Fermentation Process of Fuzhuan Brick Tea.

The pile fermentation process of Fuzhuan brick tea is unique in that it involves preheating without the use of starter cultures. The detailed metabolite changes and their drivers during this procedure are not known. Characterizing these unknown changes that occur in the metabolites and microbes during pile fermentation of Fuzhuan brick tea is important for industrial modernization of this traditional fermented food. Using microbial DNA amplicon sequencing, mass spectrometry-based untargeted metabolomics, and feature-based molecular networking, we herein reveal that significant changes in the microbial community occur before changes in the metabolite profile. These changes were characterized by a decrease in Klebsiella and Aspergillus, alongside an increase in Bacillus and Eurotium. The decrease in lysophosphatidylcholines, unsaturated fatty acids, and some astringent flavan-3-ols and bitter amino acids, as well as the increase in some less astringent flavan-3-ols and sweet or umami amino acids, contributed importantly to the overall changes observed in the metabolite profile. The majority of these changes was caused by bacterial metabolism and the corresponding heat generated by it.

Dorsal Root Entry Zone Lesioning Following Unresponsive Spinal Cord Stimulation for Post-Traumatic Neuropathic Pain.

OBJECTIVE: Spinal cord stimulation (SCS) and dorsal root entry zone (DREZ) lesioning are important therapeutic options for intractable post-traumatic neuropathic pain (PNP). However, surgical choice is controversial due to the need to maximize pain relief and reduce complications. This study aims to retrospectively analyze the effect and complications of DREZ lesioning for patients with PNP who were unresponsive to SCS and provide a surgical reference. METHODS: Demographic data and surgical characteristics of patients with PNP who underwent DREZ lesioning after an unresponsive SCS were reviewed. Long-term outcomes including numeric rating scale, global impression of change, and long-term complications were assessed. Kaplan-Meier analysis was used to evaluate pain-free survival. RESULTS: Of 19 patients with PNP, 8 had brachial plexus injury (BPI), 7 had spinal cord injury, 2 had cauda equina injury, 1 had intercostal nerve injury, and 1 had lumbosacral plexus injury. All patients were unresponsive or had a recurrence of pain after SCS, with an average pain-relief rate of 9.3%. After DREZ lesioning, the mean numeric rating scale scores significantly decreased from 7.6 ± 1.5 to 1.8 ± 1.7, with an average pain-relief rate of 75.3%. Seven patients (36.8%) experienced worsened neurologic dysfunction at the last follow-up. Patients with BPI had a significantly better outcome than other pathologies (P < 0.001) after DREZ lesioning. CONCLUSIONS: DREZ lesioning is an effective alternative procedure to SCS for patients with PNP who have lost limb function. Particularly for those with BPI, DREZ lesioning has shown good efficacy and can be considered a preferred surgical option.

Radiomics features from 3D-MPRAGE imaging can differentiate temporal-plus epilepsy from temporal lobe epilepsy.

OBJECTIVE: This study aimed to differentiate temporal-plus epilepsy (TPE) from temporal lobe epilepsy (TLE) using extraction of radiomics features from three-dimensional magnetization-prepared rapid acquisition gradient echo (3D-MPRAGE) imaging data. METHODS: Data from patients with TLE or TPE who underwent epilepsy surgery between January 2019 and January 2021 were retrospectively analyzed. Thirty-three regions of interest in the affected hemisphere of each patient were defined on 3D-MPRAGE images. A total of 3531 image features were extracted from each patient. Four feature selection methods and 10 machine learning algorithms were used to build 40 differentiation models. Model performance was evaluated using receiver operating characteristic analysis. RESULTS: Eighty-two patients were included for analysis, 47 with TLE and 35 with TPE. The model combining logistic regression and the relief selection method had the best performance (area under the receiver operating characteristic curve, .779; accuracy, .875; sensitivity, .800; specificity, .929; positive predictive value, .889; negative predictive value, .867). SIGNIFICANCE: Radiomics analysis can differentiate TPE from TLE. The logistic regression classifier trained with radiomics features extracted from 3D-MPRAGE images had the highest accuracy and best performance.

The Influence of the Strain Rate and Prestatic Stress on the Dynamic Mechanical Properties of Sandstone-A Case Study from China.

A series of conventional dynamic uniaxial compressive (CDUC) tests and coupled static dynamic loading (CSDL) tests were performed using a split Hopkinson compression bar (SHPB) system to explore the variable dynamic mechanical behavior and fracture characteristics of medium siltstone at a microscopic scale in the laboratory. In the CDUC tests, the dynamic uniaxial strength of the medium sandstone is rate-dependent in the range of 17.5 to 96.8 s-1, while the dynamic elastic modulus is not dependent on the strain rate. Then, this paper proposes a generalized model to characterize the rate-dependent strength from 17.5 to 96.8 s-1. In the CSDL tests, with increasing initial prestatic stress, the dynamic elastic modulus and dynamic strength increase nonlinearly at first and then decrease. The results show that two classical morphological types (i.e., Type I and Type II) are observed in the dynamic stress-strain response from the CDUC and CSDL tests. By scanning electron microscopy (SEM), microscopic differences in the post-loading microcrack characteristics in the behavior of Type I and Type II are identified. In Class I behavior, intergranular fracture (IF) usually initiates at or near the grains, with most cracks deflected along the grain boundaries, resulting in a sharp angular edge, and then coalesces to the main fracture surface that splits the specimen along the direction of stress wave propagation. In contrast, Class II behavior results from the combined IF and transgranular fracture (TF).

Biocompatibility and osseointegration properties of a novel high strength and low modulus ß- Ti10Mo6Zr4Sn3Nb alloy.

Introduction: Ti6Al4V titanium alloy is widely used in producing orthopedic and maxillofacial implants, but drawbacks include high elastic modulus, poor osseointegration performance, and toxic elements. A new medical titanium alloy material with better comprehensive performance is urgently needed in the clinic. Methods: Ti10Mo6Zr4Sn3Nb titanium alloy (referred to as Ti-B12) is a unique medical ß titanium alloy material developed by us. The mechanical properties of Ti-B12 depict that it has advantages, such as high strength, low elastic modulus, and fatigue resistance. In our study, the biocompatibility and osseointegration properties of Ti-B12 titanium alloy are further studied to provide theoretical guidance for its clinical transformation. Results and Discussion: The titanium alloy Ti-B12 displays no significant effect on MC3T3-E1 cell morphology, proliferation, or apoptosis in vitro. Neither Ti-B12 titanium alloy nor Ti6Al4V titanium alloy depicts a significant difference (p > 0.05); Ti-B12 material extract injected into the abdominal cavity of mice does not cause acute systemic toxicity. The skin irritation test and intradermal irritation test reveal that Ti-B12 does not cause skin allergic reactions in rabbits. Compared to Ti6Al4V, Ti-B12 titanium alloy material has more advantages in promoting osteoblast adhesion and ALP secretion (p < 0.05). Although there is no significant difference in OCN and Runx2 gene expression between the three groups on the 7th and 14th days of differentiation induction (p > 0.05), the expression of Ti-B12 group is higher than that of Ti6Al4V group and blank control group. Furthermore, the rabbit in vivo test present that 3 months after the material is implanted in the lateral epicondyle of the rabbit femur, the Ti-B12 material fuses with the surrounding bone without connective tissue wrapping. This study confirms that the new ß-titanium alloy Ti-B12 not only has low toxicity and does not cause rejection reaction but also has better osseointegration performance than the traditional titanium alloy Ti6Al4V. Therefore, Ti-B12 material is expected to be further promoted in clinical practice.

Regulating the Interplay at the Buried Interface for Efficient and Stable Carbon-Based CsPbI2Br Perovskite Solar Cells.

Buried interface modification is promising for preparing high-performance perovskite solar cells (PSCs) by improving the film quality and adjusting the interfacial energy level alignment. In this work, multifunctional ethylenediaminetetraacetic acid diammonium (EAD)-modulated ZnO is employed as an effective buried interface to regulate the interplay between SnO2 and CsPbI2Br in carbon-based inorganic PSCs (C-IPSCs). The burying of EAD into the ZnO interlayer not only enhances the photoelectric properties of ZnO by passivating oxygen defects but also adjusts the energy level alignment of the buried interface. More importantly, the perovskite quality is optimized and the buried interface defects are passivated due to the formation of coordination and hydrogen bondings. Benefiting from such a robust and efficient charge transfer configuration, a maximum power conversion efficiency of 14.58% is achieved in the optimized device, which represents the highest performance reported among those of low-temperature CsPbI2Br C-IPSCs. In addition, the unencapsulated device demonstrates better long-term and thermal stability.

Architecturally simple organic photodiodes with highly competitive figures of merit via a facile self-assembly strategy.

Photodetectors (PDs) based on organic materials exhibit potential advantages such as low-temperature processing, and superior mechanical properties and form factors. They have seen rapid strides toward achieving performance metrics comparable to inorganic counterparts. Here, a simplified device architecture is employed to realize stable and high-performance organic PDs (OPDs) while further easing the device fabrication process. In contrast to the sequential deposition of the hole blocking layer (HBL) and active layer (conventional 'two-step' processing), the proposed strategy forms a self-assembled HBL and active layer in a 'single-step' process. A high-performance UV-Vis-NIR OPD based on the PM6:BTP-eC9 system is demonstrated using this cost-effective processing strategy. The green solvent processed proof-of-concept device exhibits remarkable responsivity of ∼0.5 A W-1, lower noise current than conventional two-step OPD, ultrafast rise/fall times of 1.4/1.6 µs (comparable to commercial silicon diode), and a broad linear dynamic range of 140 dB. Importantly, highly stable (light and heat) devices compared to those processed by the conventional method are realized. The broad application potential of this elegant strategy is proven by demonstrating the concept in three representative systems with broadband sensing competence.

Global trends in research of glutamate in epilepsy during past two decades: A bibliometric analysis.

Epilepsy affects more than 70 million people in the world. It is characterized by recurrent spontaneous seizures, and it is related to many neurological, cognitive, and psychosocial consequences. Glutamate neurotransmitter dysfunction has essential functions in the pathophysiology of epilepsy. In this work, bibliometric analysis was conducted to explore the trends, frontiers, and hotspots of the global scientific output of glutamate in epilepsy research in the past 20 years. The Science Citation Index Expanded of the Web of Science Core Collection (WoSCC) was searched to obtain information on publications and records published between 2002 and 2021. VOSviewer and CiteSpace were used to conduct bibliometric and visual analyses on the overall distribution of annual output, major countries, active institutions, journals, authors, commonly cited literature, and keywords. The impact and quality of the papers were assessed using the global citation score (GCS). Four thousand eight hundred ninety-one publications were retrieved in total. During the past two decades, the number of publications (Np) associated with glutamate in epilepsy has risen yearly. The United States has published the most papers; its H-index and number of citations are also the highest. The League of European Research Universities (LERU) was the most productive institution. In 2016, the total score of the paper written by Zhang Y was 854, ranking first. The keywords that appear most frequently are "epilepsy," "glutamate," "temporal lobe epilepsy (TLE)," "hippocampus," and "seizures." This study showed that although the publications related to epileptic glutamate fluctuated slightly, the Np increased overall. The United States is a great creator and influential country in this field. The first three authors are Eid, T., Aronica, E., and Smolders, I. "spectrum," "animal model," "inflammation," "mutation," "dysfunction," and "prefrontal cortex" are increasing research hotspots. By recognizing the most critical indicators (researchers, countries, research institutes, and journals of glutamate release in epilepsy research), the research hotspot of glutamate in epilepsy could help countries, scholars, and policymakers in this field enhance their understanding of the role of glutamate in epilepsy and make decisions.

Techniques of Frameless Robot-Assisted Deep Brain Stimulation and Accuracy Compared with the Frame-Based Technique.

BACKGROUND: Frameless robot-assisted deep brain stimulation (DBS) is an innovative technique for leads implantation. This study aimed to evaluate the accuracy and precision of this technique using the Sinovation SR1 robot. METHODS: 35 patients with Parkinson's disease who accepted conventional frame-based DBS surgery (n = 18) and frameless robot-assisted DBS surgery (n = 17) by the same group of neurosurgeons were analyzed. The coordinate of the tip of the intended trajectory was recorded as xi, yi, and zi. The actual position of lead implantation was recorded as xa, ya, and za. The vector error was calculated by the formula of √(xi - xa)2 + (yi - ya)2 + (zi - za)2 to evaluate the accuracy. RESULTS: The vector error was 1.52 ± 0.53 mm (range: 0.20-2.39 mm) in the robot-assisted group and was 1.77 ± 0.67 mm (0.59-2.98 mm) in the frame-based group with no significant difference between two groups (p = 0.1301). In 10.7% (n = 3) frameless robot-assisted implanted leads, the vector error was greater than 2.00 mm with a maximum offset of 2.39 mm, and in 35.5% (n = 11) frame-based implanted leads, the vector error was larger than 2.00 mm with a maximum offset of 2.98 mm. Leads were more posterior than planned trajectories in the robot-assisted group and more medial and posterior in the conventional frame-based group. CONCLUSIONS: Awake frameless robot-assisted DBS surgery was comparable to the conventional frame-based technique in the accuracy and precision for leads implantation.

Controllable Heterogenous Seeding-Induced Crystallization for High-Efficiency FAPbI3 -Based Perovskite Solar Cells Over 24.

The addition of small seeding particles into a supersaturated solution is one among the most effective approaches to obtain high-quality semiconductor materials via increased crystallization rates. However, limited study is conducted on this approach for the fabrication of perovskite solar cells. Here, a new strategy-"heterogenous seeding-induced crystallization (hetero-SiC)" to assist the growth of FAPbI3 -based perovskite is proposed. In this work, di-tert-butyl(methyl)phosphonium tetrafluoroborate is directly introduced into the precursor, which forms a low-solubility complex with PbI2 . The low-solubility complex can serve as the seed to induce crystallization of the perovskite during the solvent-evaporation process. Various in situ measurement tools are used to visualize the hetero-SiC process, which is shown to be an effective way of manipulating the nucleation and crystal growth of perovskites. The hetero-SiC process greatly improves the film quality, reduces film defects, and suppresses nonradiative recombination. A hetero-SIC proof-of-concept device exhibits outstanding performance with 24.0% power conversion efficiency (PCE), well over the control device with 22.2% PCE. Additionally, hetero-SiC perovskite solar cell (PSC) stability under light illumination is enhanced and the PSC retains 84% of its initial performance after 1400 h of light illumination.

Microbial and Nonvolatile Chemical Diversities of Chinese Dark Teas Are Differed by Latitude and Pile Fermentation.

Understanding the microbial and chemical diversities, as well as what affects these diversities, is important for modern manufacturing of traditional fermented foods. In this work, Chinese dark teas (CDTs) that are traditional microbial fermented beverages with relatively high sample diversity were collected. Microbial DNA amplicon sequencing and mass spectrometry-based untargeted metabolomics show that the CDT microbial ß diversity, as well as the nonvolatile chemical α and ß diversities, is determined by the primary impact factors of geography and manufacturing procedures, in particular, latitude and pile fermentation after blending. A large number of metabolites sharing between CDTs and fungi were discovered by Feature-based Molecular Networking (FBMN) on the Global Natural Products Social Molecular Networking (GNPS) web platform. These molecules, such as prenylated cyclic dipeptides and B-vitamins, are functionally important for nutrition, biofunctions, and flavor. Molecular networking has revealed patterns in metabolite profiles on a chemical family level in addition to individual structures.

Manipulating Crystallization Kinetics in High-Performance Blade-Coated Perovskite Solar Cells via Cosolvent-Assisted Phase Transition.

Manipulating the perovskite solidification process, including nucleation and crystal growth, plays a critical role in controlling film morphology and thus affects the resultant device performance. In this work, a facile and effective ethyl alcohol (EtOH) cosolvent strategy is demonstrated with the incorporation of EtOH into perovskite ink for high-performance room-temperature blade-coated perovskite solar cells (PSCs) and modules. Systematic real-time perovskite crystallization studies uncover the delicate perovskite structural evolutions and phase-transition pathway. Time-resolved X-ray diffraction and density functional theory calculations both demonstrate that EtOH in the mixed-solvent system significantly promotes the formation of an FA-based precursor solvate (FA2 PbBr4 ·DMSO) during the trace-solvent-assisted transition process, which finely regulates the balance between nucleation and crystal growth to guarantee high-quality perovskite films. This strategy efficiently suppresses nonradiative recombination and improves efficiencies in both 1.54 (23.19%) and 1.60 eV (22.51%) perovskite systems, which represents one of the highest records for blade-coated PSCs in both small-area devices and minimodules. An excellent VOC deficit as low as 335 mV in the 1.54 eV perovskite system, coincident with the measured nonradiative recombination loss of only 77 mV, is achieved. More importantly, significantly enhanced device stability is another signature of this approach.

Efficacy of caudal pedunculopontine nucleus stimulation on postural instability and gait disorders in Parkinson's disease.

OBJECTIVES: Gait-related symptoms like postural instability and gait disorders (PIGD) inexorably worsen with Parkinson's disease (PD) deterioration and become refractory to current available medical treatment and deep brain stimulation (DBS) of conventional targets. Pedunculopontine nucleus (PPN) deep brain stimulation (DBS) is a promising method to treat PIGD. This prospective study aimed to clarify the clinical application of PPN-DBS and to explore effects of caudal PPN stimulation on PIGD. METHODS: Five consecutive PD patients with severe medication-resistant postural instability and gait disorders accepted caudal PPN-DBS. LEAD-DBS toolbox was used to reconstruct and visualize the electrodes based on pre- and postoperative images. Outcomes were assessed with Movement Disorder Society (MDS)-Sponsored Revision of the Unified Parkinson's Disease Rating Scale (MDS-UPDRS), gait-specific questionnaires, and objective gait analysis with GAITRite system. RESULTS: MDS-UPDRS subitems 35-38 scores were improved at postoperative 6 months (mean, 4.40 vs 11.00; p = 0.0006) and 12 months (mean, 5.60 vs 11.00; p = 0.0013) compared with baseline, and scores at 6 months were slightly lower than scores at 12 months (mean, 4.40 vs 5.60; p = 0.0116). Gait and Falls Questionnaire, New Freezing of Gait Questionnaire, and Falls Questionnaire scores also significantly improved at postoperative 6 months and 12 months compared with baseline. In addition, cadence, bilateral step length, and bilateral stride length significantly increased when PPN On-stimulation compared with Off-stimulation. CONCLUSIONS: This study suggested that caudal PPN low-frequency stimulation improved PIGD for PD patients at the 6- and 12-month period.